How to Add 2007 Saab 9-3 Key by Xhorse VVDI2 and VVDI Prog?

How-to: add a new spare key to a 2007 Saab 9-3 using the Xhorse VVDI2 & VVDI Prog. The procedure also calculate the PIN.

Some users struggle to obtain the PIN for Saab’s and cannot program via OBD. The method here will overcome this problem.

 

 

Steps:

1.Remove CIM unit

2. Read EEPROM data

3. File make key

4. Write back new dump

 

Procedure:

1.

Carefully remove the CIM unit from this Saab 9-3

It needs time, be patient.

Then remove the case and locate eeprom chip

 

vvdi2-vvdi-prog-2007-saab-9-3-key-1

 

vvdi2-vvdi-prog-2007-saab-9-3-key-2

 

vvdi2-vvdi-prog-2007-saab-9-3-key-3

 

vvdi2-vvdi-prog-2007-saab-9-3-key-4

 

2.

 

vvdi2-vvdi-prog-2007-saab-9-3-key-5

 

vvdi2-vvdi-prog-2007-saab-9-3-key-6

 

 

You can use a video microscope to identify the chip that needed reading. If found the chip and could’d see what number chip it was, spaying the chip with some brake cleaner.

did the trick and don’t worry, this is safe and won’t cause any damage.

 

vvdi2-vvdi-prog-2007-saab-9-3-key-7

Desolder the chip and soldered in to the EEPROM adapter included with xhorse VVDI Prog.

 

 

vvdi2-vvdi-prog-2007-saab-9-3-key-8

Connect VVDI2 and VVDI Prog to PC via USB
In VVDI Prog software, select EEPROM->Microchip-> 93C/LC/AA66A (8 PIN)

 

 

vvdi2-vvdi-prog-2007-saab-9-3-key-9

 

vvdi2-vvdi-prog-2007-saab-9-3-key-10

 

 

Read data success
Save data to PC

3.

In VVDI2 software, select Immo Data Tool
Select Area, brand, car and type

 

vvdi2-vvdi-prog-2007-saab-9-3-key-11

Choose Load EEPROM dump and upload eeprom file saved by vvdiprog

 

 

vvdi2-vvdi-prog-2007-saab-9-3-key-12

Select Key position

 

 

vvdi2-vvdi-prog-2007-saab-9-3-key-13

Place new key in VVDI2
Press Make dealer key

 

 

vvdi2-vvdi-prog-2007-saab-9-3-key-14

Pick PCF7936(PCF7946) as transponder type
Prepare dealer key success. It can start engine after write back new dump file or learnt it to car.

 

 

vvdi2-vvdi-prog-2007-saab-9-3-key-15

 

 

Save new key dump file to PC

4.

 

vvdi2-vvdi-prog-2007-saab-9-3-key-16

In VVDI Prog, open new key dump file

 

 

vvdi2-vvdi-prog-2007-saab-9-3-key-17

Write new data to chip

 

 

vvdi2-vvdi-prog-2007-saab-9-3-key-18

Then verify

 

Then install CIM unit back to car.

Test new key.

Done.

www.vvdishop.com

http://blog.vvdishop.com/xhorse-vvdi2-vvdi-prog-file-make-2007-saab-9-3-key/

Leave a Reply

Your email address will not be published. Required fields are marked *

89 − 87 =