How to use VVDI2 to Add Key on VW Transporter Caravelle T5 2011

If you have Xhorse VVDI2 VAG key programmer to add dealer key on VW Transporter/Caravelle T5 2011, but not work, you must read this post, the problem is finally solved.


Problem description:

VW Transporter/Caravelle T5 2011. Had an existing working key and used Xhorse VVDI2 to make a dealer key on a UDS cluster but something went wrong or more likely I did something wrong. It says 2-2 on the cluster and lights go off as if programmed but once cranked it starts and dies and the glow plug indicator light flashes. I stripped the cluster and tried with putting the cluster in to service mode but still much the same. With AD100 it says 2 keys coded and cluster in Mode 7. A friend came with his Zedfull and recoded in both keys and it said precoding ok but still the same issue. The dump of the original 24c64 and the backup I first made are attached and I’d appreciate any advice or help on this. Thanks everyone


folder: Transporter T5 24c64 Original Read

Folder: Transporter T5

UDS Dash Info


Config: This value contain car manufacture, key number, immobilizer status (new, learned, closed), keyless or not etc.


Your immo status is likely changed, did you press the reset immo button.

When did you made the 24c64 backups.

After entering service mode true obd, or after your keylearning procedure?



The initial backup (small file)was made before I made the key but I read the 24c64 only after it wouldn’t start. Any idea how to change the config from o7 to 06 again?


Instruction guide by senior:

go in to service mode by obd.

read immo data.

change the conf 7 in to 6.

press, write immo data.

press, reset instrument.

that should do it.


Finally! Solved

Thanks everyone. Yes it was me being stupid, I think I actually wrote the 24c64 complete file back instead of the smaller immo file. Did as advised and problem solved.

(Solved) VVDI2 make a dealer key on VW Transporter UDS Cluster Problem

VVDI Key Tool Renew Cable for VVDI and MK3 MasterKey III

Note: Xhorse VVDI Key Tool renew adapters package comes with a renew adapter cable that can be used with MasterKey III MK3 key programmer.


Function of the VVDI Key Tool Adapters:

can renew different kinds of used original remote keys.

Key Renew Adapters, 12pcs/set,it is used to work with VVDI KEY TOOL remote maker.




VVDI key tool renew adapter in detail:















VVDI Key Tool Renew Adapter Cable for MK3 MasterKey III

How to read Audi EZS Kessy EEPROM J518 by VVDI2

Here is the instruction showing the capabilities of the Xhorse VVDI2 VAG key programmer: Reading EEPROM with EZS Audi A6 / Q7
How to read eeprom from EZS AUDI by OBD with VVDI2:
Select Key Learn->4th immobilizer system- Audi-> A6L/Q7/Allroad
A6L/Q7/Allroad EZS-Kessy (J518) 4th immobilizer system
Select Auodetect from engine (ECU)
reading data, please wait
Reading data success
Read and save EZS-Kessy EEPROM (J518)
Start security login
Reading data…
Reading data success
Save eeprom
click on Read VIN
VVDI2 Read Audi VIN successfully.

Xhorse VVDI Prog V4.5.9 Update Polish Language and Many ECUS

Xhorse VVDI PROG ECU, MCU eeprom programmer software released to V4.5.9 on 28th, June 2017. 4.5.9 VVDI programmer adds Polish language and many ECUs.
v4.5.9 VVDIProg Update Feature (2017-06-28)
* This version DON’t need update firmware
* Fix some bugs
+ Add VVDI-PROG USER MUNUAL 4.5.9 version in Doc folder
* Update polish language
+ Update V850 D-Flash format conversion tool
* Fix STM8 series options error
* Fix MED17.1 option error
* Fix V850E-DG3 diagram error
* Fix ME17.9.11.1 diagram error
* Fix BAOJUN630 diagram error
+ Add MPC5606B, MPC5607B, MPC5602D, MPC5606E, MPC5601P, MPC5602S, MPC5604S options
+ Add SPC560B50B2, SPC560B64L3, SPC560C40L1, SPC560C50L1, SPC56AP54L3, SPC56AP54L5,
SPC56AP60L3, SPC56AP60L5 options in <2-MCU>-><ST-SPC560XXXX>
+ Add MT60(TC1766) option in <3-ECU>-><DELPHI>
+ Add V3 diagram in <3-ECU>-><DELPHI>-><MT80(TC1766)>
+ Add KESSY(2008–) option in <4-IMMOBILIZER>-><VOLKSWAGEN>
(Need to use with VVDI2,support Touareg, Bentley, A8, Cayenne, Phaeton with kessy module (IMMO4 system) after 2008)
+ Add SENOVA-D70 option in <5-DASHBORAD>-><BAICMOTOR>
+ Add EXCELLEGT option in <5-DASHBORAD>-><BUICK>
+ Add AVEO option in <5-DASHBORAD>-><CHEVROLET>
+ Add FIESTA option in <5-DASHBORAD>-><FORD>
+ Add K5(2017) option in <5-DASHBORAD>-><KIA>
+ Add FREELANDER(2004) option in <5-DASHBORAD>-><LANDROVER>
+ Add MG3(2016) option in <5-DASHBORAD>-><SAICMOTOR>
+ Add EXCELLEGT-SRS option in <7-ARIBAG>-><BUICK>
+ Add ALSVIN-SRS option in <7-ARIBAG>-><CHANGAN>
+ Add CITY-SRS(MPC5604P) option in <7-ARIBAG>-><HONDA>
+ Add 2008-SRS option in <7-ARIBAG>-><PEUGEOT>
+ Add SRS-VW20LE(SPC560P50L3) option in <7-ARIBAG>-><VOLKSWAGEN>
+ Add A4L-LWR-MODULE(2010), A6L-C6-AMP, A8L-AMB-MODULE(2011), ESL-HC08GR16-V2 options in <8-OTHER>-><AUDI>
+ Add 528-SEAT-MODULE option in <8-OTHER>-><BMW>

Free Download and update Condor XC-Mini Software to V4.0.1

Latest Xhorse ikeycutter Condor XC-mini key cutting machine software goes to V4.0.1.


How to Update Condor XC-Mini Key cutting machine online?
1. Connect iKeycutter CONDOR XC-MINI Master to the PC with a USB cable.
Turn on the iKeycutter Mini Condor Master, check old software  version
Free Download Condor Mini V4.0.1 Update tool for both S/N KM03 and KM02 here (check new update info. as well):
Unzip the update tool, open Cutterkey Tools
Come to Key Data Customize Tool menu, click on “Update” tab
Select Condor mini key cutting machine serial number, KM02 or KM03
Select newest software 4.0.1, press on “Update Online”
The Update takes minutes, please wait and do not turn off or disconnect mini Condor during the procedure.
Update Successfully

(Solved) VVDI Key Tool unknow Software Hardware version


hello good day, can you help me please? I have updated my Xhorse VVDI key tool remote generator, but then nothing display in the screen, shows SN, SW, HW (serial number, hardware, software) unknown error, device can not use, how to solve?



Do not try to update your vvdi key tool!!!



How to solve the error?

If you already updated vvdi remote maker by mistake, please wait for the authorized update tool download. When it is available, we will post the download link on both webpage and blog.


You can also contact customer service to get the new update tool.

How to solve VVDI Key Tool SN HW SW Unknown Error

Condor XC-Mini V4.0.1 Software Update Feature 2016-06-16 has provided Condor XC-Mini key cutting machine V4.0.1 update tool download for S/N KM03 in May,2017.  Now new update tool 4.0.1 for both SN KM02 and KM03 is released on 16-06-2017.


Condor Mini V4.0.1 Update Feature (2017.06.16):
+Add universal key decode function
+Add M2-D function
+Add motor sensor testing function
*Modify probe/cutter detection
*Fix machine may crash error problem
*Fix HU49 key decode error
*Fix HU66 cutting speed issue
*Fix BW6 cutting error
*Fix TBE1 cutting error
1.New update for both SN KM02/KM03 machines
2.New function:Main Interface-Key Duplication-Universal Type
3.Universal Type support decode/cutting parts of home & vehicle keys
4.Please keep the whole key clean and conductivity good(ensure without dust/oil)
5.For one side key(thickness of whole key usually 1.5mm or 2.00mm) please add a shim/business card under the key,ensure the whole key thickness should more than 3mm
Free Download Condor XC Mini V4.0.1 Update Tool
How to Update Condor XC Mini Key cutting machine online?
1. Connect iKeycutter CONDOR XC-MINI Master to the PC with a USB cable.
2. Turn on the iKeycutter Mini Condor Master.
3. Click “Update online” button to start update.
4. The screen will appear “Updating” prompt.
5. Wait for the update completed.
A: Do NOT turn off PC or unplug USB cable during updating.
B: Data downloading and firmware upgrading may take a while, please be patient.
C: If the update fails, turn off anti-virus software and then try again.

How to Unlock Remote Key with VVDI key Tool

Xhorse VVDI Key Tool remote generator Unlock remote key in test






  • Remote Generation: convert universal blank remotes into remotes that you can program into your customer’s vehicles. Add the blade and chip to complete, then program into the vehicle the same way you would the OEM remote. REDUCE YOUR INVENTORY!
  • Remote Testing: confirms your remote is working and identifies type and frequency. Supports 27-900 MHz for frequency test, 300-450 MHz for power test.
  • Transponder Identification
  • Transponder Generation (coming soon!)
  • Transponder Cloning (coming soon!)
  • Remote Unlocking (coming soon!–may involve an addition cost)

Xhorse VVDI Key Tool Unlock OEM Remote Key in Test

VVDI2 Adds Key for Passat 2013 NEC 24C64 Dash by OBD

Here is the guide to use Xhorse VVDI2 VAG key programmer to add key for Passat 2013 with VDO NEC+24C64 dashboard by OBD.


VVDI2 adds Passat 2013 Key Guide:

Go to VVDI2 software-> select VW car brand



Select Key Learn->4th Immobilizer system-VW/Skoda/Seat->Auto detect type
VVDI2 read VIN ECU and dash type: NEC+24C64

Click on Diagnosis

Click on Read EEPROM/FLASH
Select Read eeprom, click on Next

Turn ignition to ON position (If it is smart key, turn ignition OFF then turn it ON)

Dash instrument screen is in black, it is normal


Follow VVDI2 key programmer prompts:

1.Dashboard is in black, complete following steps to activate the dash:

2.Read and save eeprom data

3.Read and save IMMO data

4.Generate a dealer key (if has working key and does not need to add a key, skip to Step 7)

5. Reset dash

6.Key learning from immo data

7. Other functions

Reading eeprom data
Dave eeprom data

Read Immobilizer data
Save immo data

Click on Generate Dealer Key


Choose car manufacture->VW

Select Prepare normal dealer key

Insert car key into vvdi2 VW


click Next
confirm YES to generate VW normal dealer key

Generate dealer key success


all preclude done


Reset dash


Reset success. Dash activated.


Select Add key

(Make sure you have backup both eeprom and immo data)


Select 2nd option to do key learning and enter key numbers to to learned
click on Next

Turn ignition to ON position (If it is smart key, turn ignition OFF then turn it ON)
Confirm if it is smart key


If the dash display 1-2, insert next key into VVDI2’s coil


Insert second key within 5 seconds, turn ignition ON for 2 seconds, dash displays 2-2

Key Learning success


Start engine with the new key.


VVDI2 VAG Add Key for Passat 2013 VDO NEC+24C64 Dash by OBD