VVDI2 VAG Archives | Page 3 of 3 | Xhorse VVDI Tools Software and Hardware

20. July 2017.

How to use VVDI2 to Add Key on VW Transporter Caravelle T5 2011

If you have Xhorse VVDI2 VAG key programmer to add dealer key on VW Transporter/Caravelle T5 2011, but not work, you must read this post, the problem is finally solved.

Problem description:

VW Transporter/Caravelle T5 2011. Had an existing working key and used Xhorse VVDI2 to make a dealer key on a UDS cluster but something went wrong or more likely I did something wrong. It says 2-2 on the cluster and lights go off as if programmed but once cranked it starts and dies and the glow plug indicator light flashes. I stripped the cluster and tried with putting the cluster in to service mode but still much the same. With AD100 it says 2 keys coded and cluster in Mode 7. A friend came with his Zedfull and recoded in both keys and it said precoding ok but still the same issue. The dump of the original 24c64 and the backup I first made are attached and I’d appreciate any advice or help on this. Thanks everyone

folder: Transporter T5 24c64 Original Read

Folder: Transporter T5

Advice:

Config: This value contain car manufacture, key number, immobilizer status (new, learned, closed), keyless or not etc.

Your immo status is likely changed, did you press the reset immo button.

When did you made the 24c64 backups.

After entering service mode true obd, or after your keylearning procedure?

Question:

The initial backup (small file)was made before I made the key but I read the 24c64 only after it wouldn’t start. Any idea how to change the config from o7 to 06 again?

Instruction guide by senior:

go in to service mode by obd.

read immo data.

change the conf 7 in to 6.

press, write immo data.

press, reset instrument.

that should do it.

Finally! Solved

Thanks everyone. Yes it was me being stupid, I think I actually wrote the 24c64 complete file back instead of the smaller immo file. Did as advised and problem solved.

www.vvdishop.com

(Solved) VVDI2 make a dealer key on VW Transporter UDS Cluster Problem

4. July 2017.

How to read Audi EZS Kessy EEPROM J518 by VVDI2

Here is the instruction showing the capabilities of the Xhorse VVDI2 VAG key programmer: Reading EEPROM with EZS Audi A6 / Q7

How to read eeprom from EZS AUDI by OBD with VVDI2:
Select Key Learn->4th immobilizer system- Audi-> A6L/Q7/Allroad

A6L/Q7/Allroad EZS-Kessy (J518) 4th immobilizer system

Select Auodetect from engine (ECU)

reading data, please wait

Reading data success

Read and save EZS-Kessy EEPROM (J518)
Start security login
Reading data…

Reading data success
Save eeprom

click on Read VIN

VVDI2 Read Audi VIN successfully.

http://blog.vvdishop.com/how-to-use-vvdi2-to-read-audi-eeprom-from-ezs/

9. June 2017.

VVDI2 Adds Key for Passat 2013 NEC 24C64 Dash by OBD

Here is the guide to use Xhorse VVDI2 VAG key programmer to add key for Passat 2013 with VDO NEC+24C64 dashboard by OBD.

VVDI2 adds Passat 2013 Key Guide:

Go to VVDI2 software-> select VW car brand

Select Key Learn->4th Immobilizer system-VW/Skoda/Seat->Auto detect type
VVDI2 read VIN ECU and dash type: NEC+24C64

Click on Diagnosis

Click on Read EEPROM/FLASH
Select Read eeprom, click on Next

Turn ignition to ON position (If it is smart key, turn ignition OFF then turn it ON)

Dash instrument screen is in black, it is normal

Follow VVDI2 key programmer prompts:

1.Dashboard is in black, complete following steps to activate the dash:

2.Read and save eeprom data

3.Read and save IMMO data

4.Generate a dealer key (if has working key and does not need to add a key, skip to Step 7)

5. Reset dash

6.Key learning from immo data

7. Other functions

Reading eeprom data
Dave eeprom data

Read Immobilizer data
Save immo data

Click on Generate Dealer Key

Choose car manufacture->VW

Select Prepare normal dealer key

Insert car key into vvdi2 VW

click Next
confirm YES to generate VW normal dealer key

Generate dealer key success

all preclude done

Reset dash

Reset success. Dash activated.

Select Add key

(Make sure you have backup both eeprom and immo data)

Select 2nd option to do key learning and enter key numbers to to learned
click on Next

Turn ignition to ON position (If it is smart key, turn ignition OFF then turn it ON)
Confirm if it is smart key

If the dash display 1-2, insert next key into VVDI2’s coil

Insert second key within 5 seconds, turn ignition ON for 2 seconds, dash displays 2-2

Key Learning success

Start engine with the new key.

Done!

www.vvdishop.com

VVDI2 VAG Add Key for Passat 2013 VDO NEC+24C64 Dash by OBD

7. June 2017.

VVDI2 Full Car List Key Programming by OBD

Questions before starting:

Now Xhorse VVDI2 VAGid48 is not ready. so i can’t add key passat b6 or any other vag key with id48 chip?
It programs passat b6 b7 or other id48 cars by obd?

Solution:

Not all possible over obd. Some need read out bcm2, some of them need read out with programmer, like vvdi prog or other.

Some newer Passat with ECU EDC17, if you have condor key cutting machine and with working key,

you can directly do by OBD get 6 cs and use working key get the 7th bytes cs.

If without condor, you should remove the comfort module get the eeprom,unencrypt the cs and pin from EDC17.

Some old model passat with old ECU edc16 ,yes you can by OBD but you must have working key for calculation last two CS No. No need condor authorization for this , condor authorization is only for calculation PIN CS from edc17.

Customer working experience:

Vvdi2 does passat by obd but not on 1.6tdi with pcr, I have done 2012 caddy by obd with it, f10 key by read mcu in cas4 with vvdi prog and made key with vvdi2 , I have made keys also with the key tool, I have done passat from ccm also and some other vag also.

Full key programming car list which vvdi2 full does by obd.

look the picture:

VVDI2 VAG Audi Full Key Programming Car List by OBD