VVDI2 Archives | Page 13 of 13 | Xhorse VVDI Tools Software and Hardware

29. August 2017.

Xhrose VVDI2 Program Audi Q7 2007 Remote Key Step by Step

Here vvdishop introduces 2 ways to program remote smart key on a Audi Q7 year 2007 with Xhorse VVDI2 key programmer by OBD.

Connect Xhorse VVDI2 VAG key programmer with vehicle through OBD connector

Audi Q7 OBD diagnostic connector location

The remotes to be programmed use ID8E transponder

First, we show how one of the two remotes is deprogrammed

Original key can turn on the switch, remote key to be programmed cannot.

Method 1:

Open VVDI2 software

Select Audi->Key Learn-> 4th Immobilizer system-Audi-> A6L/Q7/Allroad

Turn ignition ON

We extract the necessary information (Pin Code and Security Code) of the vehicle to access and be able to perform the final process of programming (Key Learn)

Select Autodetect from engine (ECU)

Reading data, please wait

Reading data success

We observe on the above screen the information of security codes (Pin Code and Security Cop) extracted correctly

Let’s go to the final programming process (Key Learning)

Enter number of keys to learn: 2

and press Key Learning button

Insert the dealer key into car and switch on for at least 2 seconds. The time for change key should within 5 seconds. Press OKAY button after all key is learned.

All keys successfully learned.

Method 2:

Next, we will see another method of programming.
In this case, more direct and automatic.
And with information on the status of immobilizer and possible vehicle lock by incorrect Pin Code or transponder to
real-time on-screen.

In VVDI2 Audi Menu

Select Key Learn->Key Learn

Auto detect vehicle: A6L/Q7/Allroad 2005+, CAN

Select Autodetect PIN/CS

Automatic detection / extraction of the security codes (Pin Code and Comp. Of Security)

Real-time status information of the Immobilizer: type of key / transponder and its status, access to units, number of keys programmed

Real-time information on possible vehicle lockout and remaining time for leaving it

PIN and CS Security codes successfully extracted

Enter key number in marked red area: 2

Press Learn button

Insert entry key and switch on ignition

We accept OK to finish the process once the steps are done correctly

Test the new programmed remote key.

Working.

Done!

www.vvdishop.com

21. August 2017.

How to use VVDI2 4.3.0 to program BMW FEM BDC key

Xhorse VVDI2 key programmer V4.3.0 software released BMW FEM/BDC system key programming function.

VVDI2 V4.3.0 update (2017-08-16)
*** Require firmware V4.3.0
************************************************* *********************
===== VAG V4.3.0 =====
1. Bugfix===== BMW V4.3.0 =====
1. Add BMW FEM/BDC system key learning, erase key
2. Add BMW FEM/BDC system reset KM
3. Add FEM/BDC syste backup coding, restore coding
4. Attention: FEM/BDC Key Learn is an option function, it require buy license or exchange with bonus points. Contact your dealer for help!===== Porsche V4.3.0 =====
1. Bugfix===== PSA V4.3.0 =====
1. Bugfix===== Transponder Programmer V4.3.0 =====
1. Bugfix===== J2534 V4.3.0 =====
1. Bugfix

===== Online Upate Tool V4.3.0 =====
1. Bugfix

===== Quick Start V4.3.0 =====
1. Bugfix

Free Download VVDI2 V4.3.0 software

https://mega.nz/#!W1pSRRTL!0n8OX4wshaB1s0O06SDhTR0KvO32nPHZWg4CQjBMdrA

FAQ:

Q: After activation the fem bdc it will work without tokens？
A: Yes.

VVDI2 – BMW FEM/BDC system(function released and available, just no user manual)
Users can refer to following information (3 steps for make keys:get key info->programming FEM/BDC system->make keys)

1.support make new key with ignition switch(support add spare key and all key lost, all key lost require ISN)
2.support reset FEM/BDC KM(cluster require reset manually)
3.support erase key(after erase the key position become blank position)
4.support backup coding
5.support restore coding

Notes:
1.backup coding and restore coding can direct operation generally.
2.add keys, reset KM, erase key must programming FEM/BDC system first
3.in FEM/BDC interface, if ‘get key info’ the type not support, it will show:customer should use “BMW E-sys software” program FEM/BDC system.then programming FEM/BDC system with VVDI2 BMW
4.when operation on ‘programming FEM/BDC system’interface,please don’t close this software window until all procedures completed.
5.programming FEM/BDC system, require soldering and get eeprom.（FEM 95128 chip, BDC 95256 chip）usually there are 2 same chips on the module, please refer to the software diagram, select the correct one.
6.programming FEM/BDC system,must restore the original eeprom, restore coding.if cannot restore coding or after restore coding assemble FEM/BDC module back to car,but with problem(such as the remote control cannot start the car
or the car with window problem)please use “BMW E-sys software” coding for FEM/BDC system
7.if connect power to FEM/BDC module, but the relay keep ringing,please contact technical support for help.usually operation on FEM/BDC should be ok,just need to programming.

If your vvdi2 already bind to condor,then BMW FEM/BDC = 600 USD
without condor: BMW FEM/BDC = 800usdPls note:1.Your vvdi2 must already has BMW OBD functions
2.After payment, pls give us serial number of VVDI2 and condor(if you have)

Instructions of FEM/BDC:
http://www.vvdishop.com/info/how-to-use-the-bmw-fem-bdc–18197.html

BMW FEM/BDC Authorization for VVDI2 (With Condor)

BMW FEM/BDC Authorization for VVDI2 (Without Condor)

VVDI 2 Updated to V4.3.1 (2017-08-18)
Free Download VVDI2 V4.3.1 Software
For 4.3.0 software users, just download 4.3.1 directly, no need update firmware again.

Require firmware V4.3.0
************************************************* *********************
===== VAG V4.3.1 =====
1. Copy 48 function: Support Passat B6/CC with 48 transponder
2. Bugfix

===== BMW V4.3.1 =====
1. Improvement for BMW FEM/BDC key learn
2. Bugfix

===== Porsche V4.3.0 =====
1. Bugfix

===== PSA V4.3.0 =====
1. Bugfix

===== Transponder Programmer V4.3.0 =====
1. Bugfix

===== J2534 V4.3.0 =====
1. Bugfix

===== Online Upate Tool V4.3.0 =====
1. Bugfix

www.vvdishop.com

9. August 2017.

VVDI2 and Tango Key Programmer review on BMW VAG

Topic: VVDI2 or Tango? Which is better for auto key programming?

Program keys: VVDI2 via OBD, Tango from dump

If you are going to make keys from dump and reading with a programmer buy Tango.
If you are looking to make keys over OBD buy VVDI2 is a good tool for BMW CAS/MB EZS. (read and write MB IR key)
Tango more features, VVDI2 good for OBD

Better buy VVDI2 with VVDI Prog

I personally prefer Tango good support and more features, xhorse it is also a very good for obd.
If you buy VVDI2 i also recommend complement with VVDI programmer.

Tango has guides with pics, free with standard tool

I don’t know VVDI2… but I have tango and it’s excellent so long as you have good programmers too like xprog etc. Most makes/models have guides with pics. Also many makers are free with standard tool and you can just add when you need

VVDI2 + Tango better than Zed full

If you mean original Tango and VVDI2 full…than this group will be better than zed full, thats my opinion…but there is a lot of car that you will need to remove BCM’s, immo’s…etc because vvdi2 and tango are more eeprom based tools, except vvdi2 making bmw and vag over obd2, skp900 and obdstar are obd2 tools but cant help you with fiat, opel, renault and with some few brands

VVDI2 + VVDI Prog good for VAG + BMW

If you looking only for VAG + BMW , then VVDI2 and VVDI prog is way to go. No need any other tool. In VVDI2 you have also programmer similar to Tango that you can make keys buy dump, but 90% of VAG and BMW can be done by OBD in VVDI2.

VVDI2 = VVDI + Tango + …

VVDI 2 includes all the VVDI functions, the function of Tango…. has improved remote control generation and chip identification, and also enhanced the coil’s stability
Moreover, you don’t have to connect VVD2 with a computer or other devices to identify chip or detect remote frequently.

Conclusion:

VVDI2 wins! Wins in OBD making keys! Wins in VAG + BMW key programming.

VVDI2 BMW:

Correct odometer
Generate key
Unlock key
Fix CAS computer

VVDI2 VAG:

Read & write Immo4/Immo5 system
Learn key
Program BCM remote
K-Line instrument immobilizer box
Correct odometer
Program control unit
Unlock Immo1/Immo2 firmware protection
Support data manipulation tools

VVDI2 key programmer:

Program key chip
Generate specialized chips
Immobilizer data processing tool
Other key tools
Generate remote control

www.vvdishop.com

20. July 2017.

How to use VVDI2 to Add Key on VW Transporter Caravelle T5 2011

If you have Xhorse VVDI2 VAG key programmer to add dealer key on VW Transporter/Caravelle T5 2011, but not work, you must read this post, the problem is finally solved.

Problem description:

VW Transporter/Caravelle T5 2011. Had an existing working key and used Xhorse VVDI2 to make a dealer key on a UDS cluster but something went wrong or more likely I did something wrong. It says 2-2 on the cluster and lights go off as if programmed but once cranked it starts and dies and the glow plug indicator light flashes. I stripped the cluster and tried with putting the cluster in to service mode but still much the same. With AD100 it says 2 keys coded and cluster in Mode 7. A friend came with his Zedfull and recoded in both keys and it said precoding ok but still the same issue. The dump of the original 24c64 and the backup I first made are attached and I’d appreciate any advice or help on this. Thanks everyone

folder: Transporter T5 24c64 Original Read

Folder: Transporter T5

Advice:

Config: This value contain car manufacture, key number, immobilizer status (new, learned, closed), keyless or not etc.

Your immo status is likely changed, did you press the reset immo button.

When did you made the 24c64 backups.

After entering service mode true obd, or after your keylearning procedure?

Question:

The initial backup (small file)was made before I made the key but I read the 24c64 only after it wouldn’t start. Any idea how to change the config from o7 to 06 again?

Instruction guide by senior:

go in to service mode by obd.

read immo data.

change the conf 7 in to 6.

press, write immo data.

press, reset instrument.

that should do it.

Finally! Solved

Thanks everyone. Yes it was me being stupid, I think I actually wrote the 24c64 complete file back instead of the smaller immo file. Did as advised and problem solved.

www.vvdishop.com

(Solved) VVDI2 make a dealer key on VW Transporter UDS Cluster Problem

4. July 2017.

How to read Audi EZS Kessy EEPROM J518 by VVDI2

Here is the instruction showing the capabilities of the Xhorse VVDI2 VAG key programmer: Reading EEPROM with EZS Audi A6 / Q7

How to read eeprom from EZS AUDI by OBD with VVDI2:
Select Key Learn->4th immobilizer system- Audi-> A6L/Q7/Allroad

A6L/Q7/Allroad EZS-Kessy (J518) 4th immobilizer system

Select Auodetect from engine (ECU)

reading data, please wait

Reading data success

Read and save EZS-Kessy EEPROM (J518)
Start security login
Reading data…

Reading data success
Save eeprom

click on Read VIN

VVDI2 Read Audi VIN successfully.

http://blog.vvdishop.com/how-to-use-vvdi2-to-read-audi-eeprom-from-ezs/

9. June 2017.

VVDI2 Adds Key for Passat 2013 NEC 24C64 Dash by OBD

Here is the guide to use Xhorse VVDI2 VAG key programmer to add key for Passat 2013 with VDO NEC+24C64 dashboard by OBD.

VVDI2 adds Passat 2013 Key Guide:

Go to VVDI2 software-> select VW car brand

Select Key Learn->4th Immobilizer system-VW/Skoda/Seat->Auto detect type
VVDI2 read VIN ECU and dash type: NEC+24C64

Click on Diagnosis

Click on Read EEPROM/FLASH
Select Read eeprom, click on Next

Turn ignition to ON position (If it is smart key, turn ignition OFF then turn it ON)

Dash instrument screen is in black, it is normal

Follow VVDI2 key programmer prompts:

1.Dashboard is in black, complete following steps to activate the dash:

2.Read and save eeprom data

3.Read and save IMMO data

4.Generate a dealer key (if has working key and does not need to add a key, skip to Step 7)

5. Reset dash

6.Key learning from immo data

7. Other functions

Reading eeprom data
Dave eeprom data

Read Immobilizer data
Save immo data

Click on Generate Dealer Key

Choose car manufacture->VW

Select Prepare normal dealer key

Insert car key into vvdi2 VW

click Next
confirm YES to generate VW normal dealer key

Generate dealer key success

all preclude done

Reset dash

Reset success. Dash activated.

Select Add key

(Make sure you have backup both eeprom and immo data)

Select 2nd option to do key learning and enter key numbers to to learned
click on Next

Turn ignition to ON position (If it is smart key, turn ignition OFF then turn it ON)
Confirm if it is smart key

If the dash display 1-2, insert next key into VVDI2’s coil

Insert second key within 5 seconds, turn ignition ON for 2 seconds, dash displays 2-2

Key Learning success

Start engine with the new key.

Done!

www.vvdishop.com

VVDI2 VAG Add Key for Passat 2013 VDO NEC+24C64 Dash by OBD

7. June 2017.

VVDI2 Full Car List Key Programming by OBD

Questions before starting:

Now Xhorse VVDI2 VAGid48 is not ready. so i can’t add key passat b6 or any other vag key with id48 chip?
It programs passat b6 b7 or other id48 cars by obd?

Solution:

Not all possible over obd. Some need read out bcm2, some of them need read out with programmer, like vvdi prog or other.

Some newer Passat with ECU EDC17, if you have condor key cutting machine and with working key,

you can directly do by OBD get 6 cs and use working key get the 7th bytes cs.

If without condor, you should remove the comfort module get the eeprom,unencrypt the cs and pin from EDC17.

Some old model passat with old ECU edc16 ,yes you can by OBD but you must have working key for calculation last two CS No. No need condor authorization for this , condor authorization is only for calculation PIN CS from edc17.

Customer working experience:

Vvdi2 does passat by obd but not on 1.6tdi with pcr, I have done 2012 caddy by obd with it, f10 key by read mcu in cas4 with vvdi prog and made key with vvdi2 , I have made keys also with the key tool, I have done passat from ccm also and some other vag also.

Full key programming car list which vvdi2 full does by obd.

look the picture:

VVDI2 VAG Audi Full Key Programming Car List by OBD

6. June 2017.

How to Build Mercedes ECU test cables with Pinouts

This is the DIY guide for you to make Mercedes-Benz ECU test adapters on your own.

MB test cable for W202 W208 W210

MB ECU test cable for W203 W463 W639

Mercedes test cable for W204 W207 W212

MB ECU test cable for W212 W246 W166

Mercedes ECU test cable for W215 W220 W230

Mercedes-benz ecu test cable for W221

Mercedes ECU test cable for W221

Mercedes Test cable for W639

MB ESL/ELV test cable for W204 W207 W212

MB Test cable for W906

MB Test cable for W164

Mercedes test cable for W166 W246

Mercedes ecu test cable for W164

If it’s not easy for you to make Mercedes test cables on your own, you can spend some money on it. There are MB ECU test cables available in the market; technicians working for vvdishop.com tested it’s functionality.

Source: http://www.vvdishop.com/wholesale/benz-ecu-test-adaptor.html

The test cables above have been tested with

Ktag programmer

Kess v2 master

MB KEY OBD2

VVDI MB BGA Tool VVDI2

NEC57

How to build Mercedes ECU test cables yourself (with Pinouts)

23. May 2017.

How to Program Fiat Bravo Key by usinf VVDI2 Full

An old Fiat Bravo 2008 have lost all keys. Most OBD key programmers can only program its remote, but cannot program chip key. Can only write start key.

Step 1: Remove BSI

Dissemble the BSI under the dashboard which is made by Magneti Marelli company.

Step 2: Write Key

Remove BSI and open it, locate 8-foot CPU, be careful to find chip 95160. You are required to read the CPU 95160 chip data.

Solder CPU 95160 chip and read data by ecu programmer, i.e VVDI Prog and save data

You can use Xhorse VVDI2 full or TM100 key programmer to write key. For example, you use VVDI2, upload 95160 data just read.
Select region:Europe,Fiat-Bravo,2009-95160, then you will see key number and position etc info.

Select unused key position, follow prompt to insert a brand new 7936 (ID46 chip) into VVDI2

Confirm Yes if VVDI2 ask you to generate dealer key.

Generate key success and generate new 95160 chip data. Write the new data back to 95160 cpu chip.

Re-solder the cpu and reinstall BSI.

Write key success.

Step 3:

Use other key programmer to program remote, i.e X300.

http://blog.vvdishop.com/tips-to-program-fiat-bravo-2008-all-keys-lost-by-vvdi2/