Xhorse Multi Prog Archives | Page 10 of 12 | Xhorse VVDI Tools Software and Hardware

27. May 2024.

Will Xhorse Multi Prog Unlock VAG Simos PCR2.1?

Successfully read VAG Simos pcr2.1 ECU on bench.

Last time failed with this Ecu, and I noticed a issue with multi prog power adapter.
That 4 amps charger is fully induction (a/c noise in out put) once connect my usb cable to pc, mouse pad also stock due to multi prog SMPS noise.
Just connect with my old Power supply and everything works.
That ecu already bench read by fc200 so there’s no need unlock.

Checksum by multiprog.

I didn’t unlock anything …I just read flash in bench the write mod file. It reads full flash data.

pcr2.1 when start read go to 3-4amps in sec.

Xhorse Multi Prog Read and Write VAG Simos PCR2.1 1

Xhorse Multi Prog Read and Write VAG Simos PCR2.1 2

22. May 2024.

Xhorse Multi Prog Adds VAG CONTINENTAL SIMOS18.3

Xhorse Multi Prog ECU and TCU programmer released new database version V24 on May 20th, 2024.

Multi-Prog V24
2024-05-20 21:01:28
* Fix the FAW BCM-3(MC9S12G128) option in <OTHER-><FAW>-><FAW>
* Fix chip read exception problem in MPC556X and MPC555X series chip
* Fix the R7F701312 option failed to set the vibration frequency
* Fix the MC68HC711E9 and MC68HC11E9 option connection failure problem
* Fix some ME7.5 ECU connection failure problem and optimize the process
* Update the Great Wall air bag wiring diagram
+ The models of the read and write function modules that support Boot mode on the ECM are as follows：
1.VAG_CONTINENTAL_SIMOS18.3
+ Add R7F701331
option in
<MCU>-><RENESAS>-><RH850>
+ Add ST72321AR6,
ST72321AR7,
ST72321AR9,
ST72321J7,
ST72321J9,
ST72321R6,
ST72321R7,
ST72321R9,
ST72521BAR6,
ST72521BAR9,
ST72521BM9,
ST72521BR6,
ST72521BR9,
ST72F321AR6,
ST72F321AR7,
ST72F321AR9,
ST72F321J7,
ST72F321J9,
ST72F321R6,
ST72F321R7,
ST72F321R9,
ST72F521AR6,
ST72F521AR9,
ST72F521M9,
ST72F521R6,
ST72F521R9
options in
<MCU>-><ST>-><ST72XXX>
+ Add HC908EY16,
HC908GP32,
HC908GP32_UNLOCK_ERASE,
HC908JB16,
HC908JB16_UNLOCK_ERASE,
HC908QT1,
HC908QT2,
HC908QT4,
HC908QY1,
HC908QY2,
HC908QY4,
HC908Qxx_UNLOCK_ERASE options in <MCU>-><Motorola>-><MC68HC(9)08>
+ Add DELPHI_MT62.1 option in <ECU>-><BAIC>-><HYOSOW>
+ Add ACDelco GM E83 MPC5565 JTAG option in <ECU>-><BUICK>-><Regal>
+ Add NETA U BCM(SPC5744B) option in <OTHER>-><NETA>-><NETA>
+ Add W212 EPS(MC9S12XEG128) option in <OTHER>-><Mercedes>-><Mercedes>
+ Add Cayenne Steering Gear (2018-)(SPC56EL60) option in<OTHER>-><PORSCHE>-><PORSCHE>
+ Add VOLKSWAGEN-STEERING-COLUMN(R7F701312)option in <OTHER>-><VOLKSWAGEN>-><VOLKSWAGEN>
+ Add SERES AITO SF5 EPS option in <OTHER>-><SERES>-><AITO>

Press Update Online tab to update software, firmware and database.

Multi Prog pinout to VAG Simos 18.3

Supported models: Audi A3, VW Lamando, VW Teramont, VW Altlas, Skoda Superb

Working mode: Boot

Xhorse Multi Prog Adds VAG SIMOS 18.3 ECU 2

Xhorse Multi Prog Adds VAG SIMOS 18.3 ECU 3

Xhorse Multi Prog Adds VAG SIMOS 18.3 ECU 4

www.vvdishop.com

20. May 2024.

Xhorse Multi Prog Read and Write Audi Simos 18.1

Xhorse Multi Prog programmer new user feedback: Simos 18.1 read/write perfectly.

It is an Audi A1.
Select VAG Continental SIMOS18.1 protocol
Working mode: Boot mode.

Multi-prog will show the wiring diagram.
Read INT eeprom in 43s.
Read INT Flash in 4m 2s.
Need extra power supply 14V+

Read and Write VAG SIMOS 18.1 with Xhorse Multi Prog 1

Read and Write VAG SIMOS 18.1 with Xhorse Multi Prog 2

Read and Write VAG SIMOS 18.1 with Xhorse Multi Prog 3

16. May 2024.

Xhorse Multi Prog Adds VAG Simos 18.1 18.6 18.7 in Boot Mode

Xhorse Multi Prog ECU TCU programmer released new database on May 13th, 2024.

Database V23

Software V1.1.5.0

Multi-Prog V23
2024-05-13 20:52:46
* Optimize the MAC7116 option read and write process
* Update the option R7F701330 wiring diagram
* Update the option GEELY-NL-3(R7F701A03) and GEELY-DNL-5(R7F701A03) wiring diagram
* Add STM32 series lock, unlock erase and encryption judgment functions
* Update all series wiring diagrams in <MCU>-><Microchip>
* Add pic16f88x series EEPROM partition in <MCU>-><Microchip>-><pic16>
* Update SPC563MXX series chip wiring diagram
+ The models of the read and write function modules that support Boot mode on the ECM are as follows：
1.VAG_CONTINENTAL_SIMOS18.1
2.VAG_CONTINENTAL_SIMOS18.6
3.VAG_CONTINENTAL_SIMOS18.7
+ Add TC27X-40F, TC27X-40F(JTAG) options in <MCU>-><Infineon>-><TC2XXX>
+ Add MC9S12KL64_SECURED,
MC9S12KL64_UNSECURED,
MC9S12KL128_SECURED,
MC9S12KL128_UNSECURED,
MC9S12XDG256_SECURED,
MC9S12XDG256_UNSECURED,
MC9S12XDG512_SECURED,
MC9S12XDG512_UNSECURED options in <MCU>-><Motorola>-><MC9S12>
+ Add MC68HC912DT128C_SECURED,
MC68HC912DT128C_UNSECURED,
MC68HC912DG128C_SECURED,
MC68HC912DG128C_UNSECURED,
MC68HC912DG128P_SECURED,
MC68HC912DG128P_UNSECURED,
MC68HC912DJ128A_SECURED,
MC68HC912DJ128A_UNSECURED,
MC68HC912D60C_SECURED,
MC68HC912D60C_UNSECURED,
MC68HC912D60P_SECURED,
MC68HC912D60P_UNSECURED options in <MCU>-><Motorola>-><MC68HC(9)12>
+ Add HC908KX2, HC908JL16, HC908JL16_UNLOCK_ERASE, HC908JL8 options in <MCU>-><Motorola>-><MC68HC(9)08>
+ Add MC9RS08KA1,
MC9RS08KA2,
MC9RS08KA4,
MC9RS08KA8,
MC9RS08LA8 options in <MCU>-><Motorola>-><MC9S08>
+ Add MC68HC05B6(0B91T),
MC68HC05B8,
MC68HC05B16,
MC68HC705B32 options in <MCU>-><Motorola>-><MC68HC(7)05>
+ Add LONKING_FORKLIFT_INSTRUMENT(PIC16F887) option in <DASHBOARD>-><Lonking>-><Lonking>
+ Add NFINITI Q50(MC9S12XEP100_UNSECURED) option in <IMMOBILIZER>-><Infiniti>-><Infiniti>
+ Add Trumpchi GS3 POWER AIRBAG(R7F701A03)-LOCK-READ, Trumpchi GS3 POWER AIRBAG(R7F701A03)-LOCK-WRITE options in <AIRBAG>-><GACMOTOR>-><Trumpchi>
+ Add Monjaro AIRBAG(R7F701330)-LOCK-READ, Monjaro AIRBAG(R7F701330)-LOCK-WRITE options in <AIRBAG>-><GEELY>-><GEELY>
+ Add Geely Radorsensor(0N72D) option in <OTHER>-><GEELY>-><GEELY>

Xhorse Multi Prog Adds VAG Simos 18.1, 18.6, 18.7 in Boot

13. May 2024.

Xhorse Multi Prog Firmware Update Error Solution

Problem:

Trying to update Xhorse Multi Prog firmware online, but failed, it reported a file write error, and instruction timeout.

Solve Xhorse Multi Prog Failed to Update Firmware 1

Solve Xhorse Multi Prog Failed to Update Firmware 2

Solve Xhorse Multi Prog Failed to Update Firmware 3

Solution:

Delete multiprog software and install again.

Then run firmware update.

If had any problem with multi prog, send Diagnostic report to Xhorse engineer.

www.vvdishop.com

9. May 2024.

Xhorse Multi Prog Read and Write CitroenC4 IAW 6LP2.03

Xhorse Multi Prog programmer new feedback from one of our customers- read and write Citroen C4 6LP2 ECU successfully.

Vehicle: Citroën C4 1.4

ECU MAGNETI MARELLI IAW 6LP2.03

Operation mode: BDM

Use BDM frame from other brands.

Multi-prog will show you the BDM wiring diagram.

Xhorse Multi Prog Read and Write Citroen IAW 6LP2 1

Xhorse Multi Prog Read and Write Citroen IAW 6LP2 2

Xhorse Multi Prog Read and Write Citroen IAW 6LP2 3

Xhorse Multi Prog Read and Write Citroen IAW 6LP2 4

Xhorse Multi Prog Read and Write Citroen IAW 6LP2 5

Xhorse Multi Prog Read and Write Citroen IAW 6LP2 6

Xhorse Multi Prog Read and Write Citroen IAW 6LP2 7

Xhorse Multi Prog Read and Write Citroen IAW 6LP2 8

Xhorse Multi Prog Read and Write Citroen IAW 6LP2 9

22. April 2024.

Xhorse Multi Prog Read GMC Yukon Delco E92 on Bench

Xhorse Multi-Prog programmer new feedback from vvdishop.com’s customer:

GMC Yukon

GM Delco E92 ECM

Bench read ok

Bench write ok.

DTC off

Multi prog will show you bench wiring diagram.

Image attached

Xhorse Multi Prog Read and Write GM Declo E92 ECU 1

Xhorse Multi Prog Read and Write GM Declo E92 ECU 2

Xhorse Multi Prog Read and Write GM Declo E92 ECU 3

Xhorse Multi Prog Read and Write GM Declo E92 ECU 4

Xhorse Multi Prog Read and Write GM Declo E92 ECU 5

Xhorse Multi Prog Read and Write GM Declo E92 ECU 6

Xhorse Multi Prog Read and Write GM Declo E92 ECU 7

18. April 2024.

Clone BMW MSV90 DME with Xhorse Multi Prog

How-to: read and write BMW X3 MSV90 DME using Xhorse Multi Prog programmer on bench.

Read ok, write OK, checksum by multi-prog.

Steps:

Reading information from the old computer:

Select ALL from the menu.

Choose IMMOBILIZER.

Xhorse Multi Prog Read and Write BMW MSV90 1

Xhorse Multi Prog Read and Write BMW MSV90 2

Read the computer’s serial number.

Select the corresponding option and press OK.

Choose BENCH to read the information without removing the computer.

Follow the schematic to connect the cables.

Xhorse Multi Prog Read and Write BMW MSV90 8

Click on EEBROM to read the memory.

Click on FLASH to read the file.

Click on OPEN then VERIFY to ensure the file’s integrity.

Click OK to start writing.

Wait until the percentage reaches 100%.

Xhorse Multi Prog Read and Write BMW MSV90 9

Xhorse Multi Prog Read and Write BMW MSV90 10

Xhorse Multi Prog Read and Write BMW MSV90 11

Writing information to the new computer:

Select ALL from the menu.

Choose IMMOBILIZER.

Write the serial number of the new computer.

Select the corresponding option and press OK.

Choose BENCH to write the information without removing the computer.

Follow the schematic to connect the cables.

Click on EEBROM to write the memory.

Click on FLASH to write the file.

Click on OPEN then WRITE to write the file.

Wait until the percentage reaches 100%.

Starting the car:

Connect the new computer to the car. Start the car.

Notes:

Make sure to use the Xhorse MULTI BROG software version 1.44 or later. Ensure proper cable connections. Verify file integrity before writing. With these simple steps, you can successfully transfer information from an old BMW computer to a new one.

www.vvdishop.com

7. April 2024.

Xhorse Multi Prog or VVDI Prog to Write Write Volvo CEM TB28F400

In my previous test, Xhorse VVDI PROG does not work with Volvo CEM TB28F400 microcircuits . It can erase them but cannot write. Now I’ve already have the next generation Xhorse Multi-Prog Programmer respectively. And the XDMPO4GL VH24 SOP44 Adapter was purchased specifically for these microcircuits.

With the TB28F400 B5B microcircuit was installed, now let’s see a clear difference between the Multi-Prog Programmer& VVDI PROG.

Xhorse Multi Prog Read and Write Volvo CEM TB28F400 1

Open MultiProgsoftware,

Click “Read”.

Read success.

In the Device settings, I can select “Verify after reading”. It’s very useful option I strongly recommend it.

Open the prepared file.

Click “Write”.

Let’s see if it will be successful, just waiting for the result.

Writing success.

Save the file.

Xhorse Multi Prog Read and Write Volvo CEM TB28F400 2

Xhorse Multi Prog Read and Write Volvo CEM TB28F400 4

Finally, let’s compare the original file with the new saved file.

They are exactly the same.

The files are identical.

Actually, the difference between Multi-Prog & VVDI PROG is already clearly: it works with these microcircuits, not only start recording. Therefore, you need to purchase the appropriate adapter SOP44. Everything will be fine.